How to Fix Continuous Spinning of the Weed Eater String

This problem of continuous spinning of the weed eater string is very common among new users of this tool and can make your head spin just as much. But, once you get a hold of how to easily fix this problem without the need of reaching out to a professional, you’ll be back to weeding just as before.

Note: This guide refers only to gasoline weed eaters as electric weed eaters do not use the same system of operation and will not run across the same kinds of issues.

A Quick Peek

A weed eater does not come with any blades or sharp cutting tools. Instead, it uses a flexible string line that spins at a dangerously high speed to get rid of unwanted weeds in minutes. Almost every weed eater comes with a throttle for adjusting the strength of the string to a higher or lower spinning frequency.

Husqvarna 128LD 17" Cutting Path Detachable Gas String Trimmer
  • Features a 28cc 2-cycle engine which powers the 17 inch (cutting...
  • Trimmer engine runs on a mixture of unleaded gas and 2-cycle oil (2. 6...
  • Easily release new trimmer line as you work by tapping the trimmer...
  • Have no worries when it is time to replace the trimmer line - the T25...
  • A translucent fuel tank allows you to visually monitor your fuel level...

How Weed Eaters Work

how do weed eaters work?

Here’s a fast recap of how weed eaters work for newbies. To make it easier to understand, the clutch system of a weed eater is similar to the clutch system of a chainsaw – for those who are familiar with how chainsaws operate.

When you push or pull on the throttle, the string will start spinning and the speed will increase swiftly but at a consistent pace. To stop spinning, you simply release the throttle and it will come to a short end.

Where It Goes Wrong

However, at times the weed eater is prone to getting faulty just as every other tool created by mankind. At that time the string will probably continue to spin even when you release the throttle. Such a situation is quite a risky thing to handle as it can cause potential injuries to the user or damage something close by.

It is therefore highly advised that you check your weed eater thoroughly before each use – even if you’re used to working on it often.

Possible Causes of Malfunction

Possible Causes of Malfunction in Weed Eaters

When your weed eater’s string continues to spin even after you’ve released the throttle, there are two most common causes of such a problem. It might be that:

  • The engine is idling ioo quickly


  • The clutch is not functioning properly as it should be and requires servicing/repair

Both these issues can be easily corrected without the need of any expert’s attention – if you pay attention to the solutions below.

#1 – Engine Idling Too Quickly

The first thing you should check if there is a problem with the idling speed is the engine of your weed eater. Do the following below to find out whether or not the engine is idling as quickly as you think it is.

If it is idling too quickly, the clutch shoes may not be able to retract and this will cause the string trimmer to continue spinning even after you have released the throttle.

Solution for #1

You can solve this problem by tweaking the speed of the idle. This can be done quite easily.
Find the adjustment screw on the carburetor. You can identify it with the mark “I”.

Turn the screw counterclockwise while the engine is still running. This will cause the engine to slow down so that the head will be able to stop the string from spinning.

If this method does not work out well or if the head does not stop before the engine dies, you have no choice but to repair the clutch as soon as possible.

By adjusting the engine this way, you can get a much more enhanced performance and reduced fuel consumption from your weed eater. This can also be considered a maintenance trick to get the most out of your tool after some weeks of use.

Ditch The String – The Last Trimmer Head You Will Ever Need

trimmer boss review

#2 – Faulty clutch system

As mentioned previously, a chainsaw’s clutch system and a weed eater’s doesn’t vary much. So if you’re a chainsaw user, I’m sure you’ll be able to catch up on this very quickly. Weed eaters normally come with a centrifugal clutch through which its drive shaft connects to the flywheel of the engine. The centrifugal clutch is located at the engine housing’s front.

The clutch has two main components: a shoe assembly (connects to the engine) and a housing or drum (connects to the shaft of the trimmer).

The shoes are held together and compressed by the string until they are separated by the force of the engine as it spins fast enough. As they separate, they contact with the drum to turn it on. When the engine slows down, the string trimmer will pull the shoes back again and the drum is turned off.

Possible Reasons for Malfunctioning of the Clutch

There are two ways by which the clutch can possibly fail.

  • The friction coatings on the shoes can become worn out as a result of long usage. This can cause the shoes to slip against the drum. When this happens, the string head will either stop spinning or spin intermittently. The shoes could also be contaminated by oil if it gets into the clutch. This results in the functioning of the clutch being disrupted and it malfunctions.
  • The second cause of the clutch malfunctioning is due to the shoes not retracting properly and maintaining a steady contact with the drum. This usually happens when the string trimmer/weed eater is broken. Corrosion might also be a cause of it.Fortunately, you don’t have to panic as a broken string trimmer can be replaced easily. Alternatively, to ensure no other future malfunctions by the clutch system, you can preferably replace the entire clutch system too.

Solution for #2

  • Empty the fuel tank of your weed eater.
  • Remove the drive shaft, which would have been secured to the engine housing with a screw. Some models may require that you remove the throttle cable as well as the ignition wires.
  • Unscrew the single screw that keeps the clutch drum secure. You should ensure that the pistol does not move. You can prevent the pistol from moving by closing the spark plug hole with a nylon rope.

The drum will come out when you remove the screw. The removal of the drum will make it possible for you to unscrew the shoe assembly. You can choose to either replace it if it has too much damage or repair it. If you consider replacing the shoe, you might as well want to replace the drum too.

These two ways should be able to repair the continuous spinning of the string. If none of these troubleshooting solutions solve the problem when the throttle is off, you have to seek professional help to fix it thoroughly. Hope it didn’t actually get that far and you were able to do the repairs and fixings by yourself! Good luck!

Subscribe To The Lawn Care Guides Newsletter

Don't worry, we don't spam

Lawn Care Guides
Compare items
  • Total (0)